Class Schedule

Class Overview:

Day 3 – Building Energy Science

CLASSROOM: Discuss ‘Refrigerant Charge’ and ‘Equipment Calibration’.

HANDS ON: Combine the Airflow techniques with Refrigerant charge procedures, Multiple opportunities to practice on various pieces of equipment.

Class Overview:

Day 4 – Building Envelope

CLASSROOM: Discuss ‘Combustion Analysis’, ‘Room to Room Pressure Diagnostics’ and ‘Duct Leakage Diagnostics’.

HANDS ON: 80 and 95 AFUE Combustion analysis, and Room to Room pressure diagnostics including Duct Leakage Diagnostics, (finding leaks with a manometer).

Class Overview:

Day 5- Building Envelope

CLASSROOM: Discuss ‘Thermal Bypass and Quality Insulation Installation’, ‘Thermal Imaging’.

HANDS ON: Inspect a wall section, working some of the areas discussed, Use an IR camera and review the results, using a hot wall for the training.

This full day training class is designed to introduce HVAC Contractors, General building Contractors, and Mechanical Engineers to the process of sizing, designing and installing small Commercial HVAC package unit systems.

This class includes three specific components:

1. Classroom instruction of the building science affecting equipment capacity and building loads;

2. Hands on training in the use of Wrightsoft™ to size small commercial loads;

3. Classroom instruction on the proper sizing procedures in ACCA Manual CS, and California Title 24 Ventilation Regulations.

This full day training class is designed to introduce HVAC Contractors, General Building Contractors, and Mechanical Engineers to the process of duct design and register selection when installing small Commercial HVAC systems.

This class includes four specific components:

1. Classroom instruction of the ACCA Duct Design procedure.

2. Classroom instruction on effects of CFM, velocity and pressure on duct desgins and general airflow terminology.

3. Duct sizing practice exercises.

4. Register selection and placement.

This full day training class is designed to introduce HVAC Contractors, General building Contractors, and Mechanical Engineers to the process of sizing, designing and installing small Commercial HVAC Systems.

The training class includes two specific components:

1. Review of all objectives and priciples covered in the first two courses of this series.

2. Hands on software exercises guided by the instructor to verify students can properly design an HVAC package unit system for quality installation, as well as properly design the duct system.

As homes become tighter and use energy more efficiently, airflow and airflow balance is going to become increasingly important . Comfort and indoor environmental quality are dependent upon proper airflow into each room. The session starts with a classroom discussion covering the basic science and calculations involving airflow balance. Followed by a lab session that allows the material covered in the classroom to be put to practical use in a lab exercise.
Airflow measurements will be made with a flow grid and flow hood, other topics that will be demonstrated focus on the California Title 24 Part 6, approved Airflow measurement and Fan Watt efficacy calculations.

This full day training class is designed to introduce HVAC Contractors, General Building Contractors, and Mechanical Engineers to the process of duct design and register selection when installing small Commercial HVAC systems. This class includes four specific components.

1. Classroom instruction of the ACCA Duct Design procedure.

2. Classroom instruction on effects of CFM, velocity and pressure on duct desgins and general airflow terminology.

3. Duct sizing practice exercises.

4. Register selection and placement.

This full day training class is designed to introduce HVAC Contractors, General Building Contractors, and Mechanical Engineers to the process of duct design and register selection when installing small Commercial HVAC systems. This class includes four specific components.

1. Classroom instruction of the ACCA Duct Design procedure.

2. Classroom instruction on effects of CFM, velocity and pressure on duct desgins and general airflow terminology.

3. Duct sizing practice exercises.

4. Register selection and placement.

This full day training class is designed to introduce HVAC Contractors, General building Contractors, and Mechanical Engineers to the process of sizing, designing and installing small Commercial HVAC Systems. The training class includes two specific components.

1. Review of all objectives and principles covered in the first two courses of this series.

2. Hands on software exercises guided by the instructor to verify students can properly design an HVAC package unit system for quality installation, as well as properly design the duct system.